You are not logged in.

  • Register to access all forum features  

#1

ben2363
Member
Joined: 05 April 2016
Posts: 163
Member
01 July 2020 10:27 pm

looking for a second hand shaker table to run my crushed cons over.

#2

CreviceSucker
Member
Joined: 24 November 2013
Posts: 665
Member
02 July 2020 02:58 am

what type ?

gemeni tables are rated as the best thing since sliced bread but cost $ 16,000 in Oz last time i looked.

https://mineraltechnologies.com/process … udsen-bowl

They were first patented in 1986 but the patent may have expired ?? anyone got thoughts on that ?

http://www.tarnagulla.com/photogallery/ … an-Cuffley

You can also buy a copy of a gemeni table from Tanzania for $ 10,000 new , but the shipping brings it back close to the price from Mineral Technologies.

MSI sell "a copy" of the Gemeni table which is of course good old home grown american technology. i wonder if they paid royalties for that ?

I think they charge $ 35,000 for theirs .

https://www.msi-mining.com/xtruder.html

There are a few old Wifley tables around but they dont come anywhere near the Gemeni and they sell for big $$$ second hand.

What kind do you want and whats your budget ?

I am not sure if there is such a thing as cheap in a second hand gold finishing table cry

Last edited by CreviceSucker (02 July 2020 03:14 am)

1 user likes this post: ben2363

#3

bjarvie
Member
Joined: 09 September 2017
Posts: 61
Member
02 July 2020 10:16 pm

how much material do you have to run and what state are you in? Im building one atm

1 user likes this post: ben2363

#4

zippo
Newbie
Joined: 25 September 2019
Posts: 3
Newbie
13 July 2020 11:22 am

I have a post in the DIY section using a 12 v motor , if you are looking for different construction materials and ideas .

1 user likes this post: ben2363

#5

ben2363
Member
Joined: 05 April 2016
Posts: 163
Member
30 July 2020 08:33 am

Thanks heaps guys.
Im in Victoria not planning on running any thing big a tonne and under.

#6

Outback
Member
Joined: 22 August 2013
Posts: 1,388
Member
30 July 2020 11:12 pm

ben2363 wrote:

Thanks heaps guys.
Im in Victoria not planning on running any thing big a tonne and under.

Hi Ben ,
What size will you be going down to after crushing the cons ?

Think I will be able to steer you to a much cheaper alternative ' that will do what your after wink

Jack .

#7

Outback
Member
Joined: 22 August 2013
Posts: 1,388
Member
30 July 2020 11:13 pm

double post . Whoops .

Last edited by Outback (30 July 2020 11:15 pm)

#8

ben2363
Member
Joined: 05 April 2016
Posts: 163
Member
31 July 2020 03:10 pm

Screen on the crusher is 1.2mm so 1mm and under.

#9

Outback
Member
Joined: 22 August 2013
Posts: 1,388
Member
01 August 2020 10:30 pm

ben2363 wrote:

Screen on the crusher is 1.2mm so 1mm and under.

Hello Ben2363 ,

I would have given you new information to allow the recovery of gold from that crusher sized material ' But there was No appreciation shown in your reply .
Therefore there will be no info !

Lesson for us all is be polite if you want advice wink

jack

#10

ben2363
Member
Joined: 05 April 2016
Posts: 163
Member
02 August 2020 10:07 pm

thumbsup


Contact Us - Privacy Policy - Terms Of Service

View Desktop Site

Top