You are not logged in.

  • Register to access all forum features  

#1

XLOOX
Member
From: Inglewood Fault, QLD
Joined: 21 August 2019
Posts: 44
Member
09 February 2020 07:48 pm

This is a question for those with both a Pro Oz and an SL like Karelian & Ridgerunner….

I have often wondered, Does the fine GB control makes a significant diff or not to being able to properly GB the machine in hot ground?

The reason I wonder this is because I notice that with my SL in mild soil that the GB null point is not so much a point as a small range and that as you move away from that point the effect is gradual eg for a GB 8 null point, 7.25 is Screaming High Tone, 7.50 High tone, 7.75 sl chattery, 8.0 silent. 8.25 sl chattery, 8.50 low tone, 8.75 Honking low tone.

This contrasts with really hot soil where IF I can get it balanced at all it is a knife edge ie 7.9 Screaming High, 8.0 sl chattery, 8.1 Honking Low. Under these conditions the machine is then much more sensitive to variations in sweep speed, variation in height above ground etc producing lots of exciting noises as I move about. I can sort of see thru the spurious signals but it is less than ideal.

So I am wondering, ok I can see that a vernier fine GB should help in finding that knife edge null point in the first place but after both are ground balanced is the PRO Oz noticeably quieter that the SL in hot ground or not?


1985-2005 Garretts ADS Deepseeker x 2- now THATS a slow learner !
2017- current Whites TDI SL 16V, Sadie, 14x9 Evo, TRX, Nokta Gold Kruzer

#2

karelian65
Member
Joined: 16 January 2017
Posts: 150
Member
09 February 2020 11:02 pm

Just an example of the Tdi Pro being ground balanced with the Sadie coil in the beginning of the video. Much easier and faster than the Tdi SL. The ground at this site is very heavily mineralized and full of iron stone and hot rocks. Really nasty ground. Turn the volume up a bit to clearly hear the difference in ground noise between the Low and All positions on conductivity. SL users can also get some indication on how the machines compares with the Pro with regards to ground noise. Same with the bigger Digger coil. A bit of a camera sweep to show what the ground looks like and the area I was operating in.

The Pro is much easier to ground balance compared to the SL but once balanced both machines are roughly equal, perhaps a slight advantage to the Pro in really nasty ground. Hope this answers you question XLOOX .

Last edited by karelian65 (09 February 2020 11:13 pm)

1 user likes this post: XLOOX

#3

Ridge Runner
Member
Joined: 04 September 2014
Posts: 6,442
Member
10 February 2020 03:19 am

As with most Manual ground balancing Detectors, Most Pros will not try to set it perfect But they will try to set the GB slightly on the positive side, This hots up the machine making it slightly more sensitive to smaller targets and adding a fraction more depth,

If a machine only has Auto GB and a Lock / Fixed position you can still do this when pumping the Coil by stopping the coil a few inches off the ground on the down stroke and locking the GB,

Hope that helps.

J.

Last edited by Ridge Runner (10 February 2020 03:20 am)


AKA, Fridge Runner....... Thanks DD

#4

XLOOX
Member
From: Inglewood Fault, QLD
Joined: 21 August 2019
Posts: 44
Member
10 February 2020 04:44 pm

Hi Ridgrunner, thanks for that. You bring up another point I have never been clear on - running with a GB offset in ALL mode.

I can understand running an offset GB if you are in HIGH/LOW since the threshold is still silent but when you say "Set the GB slightly on the positive side" do you mean that if the GB null point is say 8 then you set the machine to 8.25 or thereabouts and still run in ALL?

If you do that don't you just get a continuous loud low sounds when sweeping? Sure a small high tone target will still cut thru but how do you know that each of the hundreds of low tone blurts isn't a huge nugget ?


1985-2005 Garretts ADS Deepseeker x 2- now THATS a slow learner !
2017- current Whites TDI SL 16V, Sadie, 14x9 Evo, TRX, Nokta Gold Kruzer

#5

Ridge Runner
Member
Joined: 04 September 2014
Posts: 6,442
Member
10 February 2020 05:07 pm

Mate the only time I would not want to hear a steady threshold was if I was using the TDI or Coin or Jewellery hunting in an Iron filled site because I would only want to here the low or high conductors, Apart from that I would always want to hear the softest of thresholds, with the volume up high and the threshold very very low, But never nulled

As for the GB you want to GB the machine and then tweak it slightly so it just starts to rise as you get the coil closer to the ground,

With the TDI SL it has what I call the smoothing effect when the GB is switched ON, The TDI Pro has this but it only does it when the GB is turned OFF, you can see that in Action with some Guys TDI Beach detecting Tips on youtube, But the TDI SL does that when the GB is switched ON so even though you off set the GB the TDI SL will settle down giving you a smooth threshold as long as you keep the coil at the same height all the time that way you can run it a bit hotter and some of the those phantom signals will be gone,

But if you off set the GB by a larger amount say from 8 to 9 some targets that are low conductors will come through as high conductors and vice versa, This is not a quick thing to learn but it is worth playing with in the back yard so you can understand and then put it to use out in the Bush or on the beach,

Hope that helps.

J.


AKA, Fridge Runner....... Thanks DD

1 user likes this post: XLOOX

#6

XLOOX
Member
From: Inglewood Fault, QLD
Joined: 21 August 2019
Posts: 44
Member
10 February 2020 05:15 pm

Neat! - I am going to play in the paddock this weekend and see what I can learn from putting that into practice...


1985-2005 Garretts ADS Deepseeker x 2- now THATS a slow learner !
2017- current Whites TDI SL 16V, Sadie, 14x9 Evo, TRX, Nokta Gold Kruzer

#7

XLOOX
Member
From: Inglewood Fault, QLD
Joined: 21 August 2019
Posts: 44
Member
07 May 2020 07:18 pm

I was reading thru the SPP threads and came across an intriguing post by Old Hand in Sept 2014 talking about replacing the GB knob with a vernier dial to improve finesse of GB adjustment. I contacted him and got the details & ordered one off ebay. Not cheap in that what started as a USD35 item ended up costing AUD100 delivered inc customs but after using it I think its worth it.

The Philmore S38 36mm vernier dial is used for ham radio and other fine tuning applications. There is an internal planetary gear system that connects the knob with the shaft. It says its 8:1 but seems like 6:1 to me ie 3 full turns (1080deg ) of the knob moves the GB shaft 180 deg. It really is a totally cool bit of mech in an increasingly elec world.

So whereas before I was struggling to move the GB 1deg - just a smidgin without overshooting against the friction & hysteresis of the pot & O-ring, now I can easily turn the knob 8 degrees to achieve the same result or even finer control and really nail that balance point, or apply a tiny offset. Sold !

To install it the old plastic GB knob simply gets prised off and the vernier dial slips on top of the GB pot shaft. It is held onto the GB pot shaft with a screw. The vernier dial body then needs to be mounted to stop it rotating when the knob is turned. Old Timer mounted his on a piece of aluminium held by the pot mounting nut but just to be different I riveted an alu tab to the MD shaft and mounted it off that.

The only thing to be aware of is that since the total movement of the vernier shaft is only 180 deg, but the GB pot shaft 0-11 is something like 300 deg travel, you wont cover the full GB range with this particular dial. Not a big deal for me. I mounted it so it works between 5.5 & 11 as I have never had soil GB less than 6 and mostly 8-9.

If you really need a much lower GB at some point, for say the beach, then you can loosen the vernier shaft screw, rotate the GB shaft half a turn with a scribe and retighten the screw to give you say 0-7.5 . Or just take it off with 2 screws & slip the old plastic knob back on for the day.

At this point, with 16V & now a vernier GB, my SL is edging closer to a Pro Oz.

Using it in the field, it works very well and definitely helps get a more precise GB when the ground/coil combo is making it hard to quieten the beast. So thanks heaps to Old Hand for a great idea.

1588839318_dsc_0146.jpg
1588839318_dsc_0147.jpg
1588839318_dsc_0163.jpg
1588839319_dsc_0164.jpg
1588839319_old_timer_spp_vernier_dial_mounting.jpg
1588839319_philmore_s38_vernier_dial_knob.jpg

Last edited by XLOOX (07 May 2020 07:31 pm)


1985-2005 Garretts ADS Deepseeker x 2- now THATS a slow learner !
2017- current Whites TDI SL 16V, Sadie, 14x9 Evo, TRX, Nokta Gold Kruzer

2 users like this post: karelian65, mbasko

#8

karelian65
Member
Joined: 16 January 2017
Posts: 150
Member
10 May 2020 01:26 pm

A simple and reversible solution to ground balancing in hot ground with a Tdi Sl. If prospecting is your main game then this is certainly going to make life easier.
I'm going to pass this one on to others, Old Hand and XLOOX full credit.

#9

nesral
Member
Joined: 05 January 2015
Posts: 259
Member
11 May 2020 10:20 am

Alternative:
I replaced the GB 17mm Pot with a 24mm Pot of same value and the 17mm audio threshold Pot with a 10 turn Pot.
Had the 5 turn Pot as GB Pot but found there was to much turning, like the 1 turn 24mm Pot better.

1589152754_project2.jpg

Correction the 10 turn Vernier with lock ..... is a 10 turn Pot rotation counter with graduated scale.

Last edited by nesral (11 May 2020 11:00 am)

#10

XLOOX
Member
From: Inglewood Fault, QLD
Joined: 21 August 2019
Posts: 44
Member
12 May 2020 08:40 pm

Hi Nesral,

I am not clear on how a 1 turn 24mm pot makes it easier to fine tune GB vs a 17mm 1 turn pot. Wouldn't they be the same Ohm/degree ?

The 5 turn pot sounds quite good actually but my soldering/desoldering skills are at a level such that I don't mind blowing up a Xtal radio kit or a veroboard door chime but I'd be too afraid to touch the electronics in my SL anyway smile


1985-2005 Garretts ADS Deepseeker x 2- now THATS a slow learner !
2017- current Whites TDI SL 16V, Sadie, 14x9 Evo, TRX, Nokta Gold Kruzer

#11

nesral
Member
Joined: 05 January 2015
Posts: 259
Member
13 May 2020 11:32 am

The track on a 24mm Lin. pot is half time longer than the track on a 17mm Lin. pot, resulting in an expanded graduated resistance.

Also possible is to use a 24mm anti-log taper pot that will expand the resistance of the last half of the track even more, good when prospecting hot ground, less so when GB is used in mild ground.

A larger knob on the GB pot also help with fine tuning.

The ADS Deepseeker have a 5 turn 10k ohm pot.


Contact Us - Privacy Policy - Terms Of Service

View Desktop Site

Top