TDI PRO Not detecting the gold it should

Prospecting Australia

Help Support Prospecting Australia:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Greglz86

Greg Anderson
Joined
May 21, 2013
Messages
831
Reaction score
353
Location
Canberra, ACT
Hey guys. Im losing confidence in the TDI Pros ability to find small gold.
Ive done a couple of air test demonstrations and wasnt impressed with the results to a point where I think it could be the detector not performing for whatever reason.
But user error is still a likely culprit :8
Threshold was higher than I wanted it to be because it was just too noisy and warbly regardless what the gain was set at so for the purpose of the test I pushed it as high as I could.
But heres the vids. What do you reckon? Personally I feel as though both coils should have picked up the .2 gram nugget a little more easily.
Greg

 
On the TDI Pro and the TDI SL on small targets on the edge of detection some times all you will hear is a Waver, NOT a woo woo sound, That waver can sound as faint as a wind noise so you need to be wearing headphones to hear it, and the threshold needs to set so you can only just hear it,

Using a loud threshold will wipe out most normal small nuggets, so run it very low and listen for the faintest of wavers, If they are that small they can even sound like ground noise and when you find one Boot scrape the ground or use your pick and see if it gets louder and keep doing that, if it does dig,

hope that helps.
 
Thanks guys. The threshold was higher than I wanted it to be. Was having a little difficulty keeping the warbling to a minimum.
Ill try again soon with gain on 5 or six and see how I go but from memory I was doing this but was still missing the small stuff.
Ill make another video for comparison.
Turned out to be a bit of a lame day. Tried to get to a area Ive been interested in for a while but after walking past 2 brown snakes and having a tiger snake charge at me I went elsewhere.
Learnt how high I can jump
 
Also, who else hates wearing headphones? Or is it just me. I wear hearing protection for easily up to 30 hours a week. Wearing headphones on my weekend doesnt make detecting enjoyable for me.
Before I sold the sdc to go towards building my house I was alternating ears. Keep one ear on and one ear off. Then after a while I just left it off.
 
Greglz86 said:
Also, who else hates wearing headphones? Or is it just me. I wear hearing protection for easily up to 30 hours a week. Wearing headphones on my weekend doesnt make detecting enjoyable for me.
Before I sold the sdc to go towards building my house I was alternating ears. Keep one ear on and one ear off. Then after a while I just left it off.

I like em because outside noises distract me a bit, with headphones I get Locked in on what's happening, Have you tried a speaker system yet, that might help and boost the signal return in the process ?.
 
Greglz86 said:
Also, who else hates wearing headphones? Or is it just me. I wear hearing protection for easily up to 30 hours a week. Wearing headphones on my weekend doesnt make detecting enjoyable for me.
Before I sold the sdc to go towards building my house I was alternating ears. Keep one ear on and one ear off. Then after a while I just left it off.
try wearing ear buds , awesome for hearing in detail whats is happening :cool:
 
1540418687_999cc6cc-a136-44a8-b9e9-b2eeab9e8455.jpg


Ive got one of these at home somewhere. Its just a el cheapo from eBay. Ill hook it up and have a go.
 
I got 2 pickers around 0.1 gram that will not register when using mono coils on the TDI Pro, even with the Super Pulse 150 (6.5") mono coil.
Both pieces will register slightly on a 10x5" F8 mono and clearly when using a 10x5" DD coil even with the threshold below audible.
My 0.2g 18k+ WA nugget will register clearly on all above coils in Low with GB at 8 and minimal threshold audio.
Needles to say my favourite small nugget coil is the 10x5"DD.
 
I would prefer to not be tied to the machine but I do use the sp01 and plugs because it does make a difference.
I run the threshold on the quiet side of the "warble" but still have some the spikes that you can hear in the video and take a bit of time doubling back over the areas that I hear the spike, (this does get frustrating).
Your Tdi seems to be on par with mine, I use a 0.25g lead peice to set up when having a swing and that is about the bottom of what I expect to find (lead is a slightly better conductor).
A while ago I was offered a Gpx4500 by a friend from work, he told me to try it out for a while so I had it for about four weeks. Running them side by side on the 0.25 test bit the Gpx was about an inch better, no doubt the gpx is better on anything under 0.5g but they leveled out at 0.5g.
Personaly I find the Tdi more user friendly.
Matt T
 

Latest posts

Top