You are not logged in.

  • Register to access all forum features  

#1

Crow Pickens
Member
From: , SA
Joined: 07 June 2017
Posts: 47
Member
11 November 2017 10:56 pm

My attempt at a portable stone crusher, been working on it for the past couple of weeks. welded to a piece of channel, leather over out let to try and stop the dust so much. ( and I use a dust mask)1510400315_4639.jpg1510399720_4636.jpg1510400461_4638.jpg
My attempt at a Miller Table, using my 8 inch sluice frame, used green chalk paint, using a small pump to reuse water, all can been run off my vehicle batteries and solar panel on top of vehicle and to recharge the batteries on grinder.1510400872_4642.jpg 1510400894_4649.jpg1510400912_4654.jpg
Now all I got to do is FIND stones to crush.
Thanks for looking
Cheers Crow Pickens


SDC 2300, Equinox 800, I am a Blessed Man

11 users like this post: Matt80, Goldfreak, BigWave, Mackka, madtuna, Dolphin, Occasional_panner, aussiefarmer, NeilM, junkdog, 7.62marksman

#2

Muk
Member
Joined: 19 June 2016
Posts: 242
Member
12 November 2017 06:48 am

Looks the goods can you put a photo of inside of the crusher good luck with the gear cheers Muk.

#3

Goldfreak
Member
Joined: 13 May 2017
Posts: 810
Member
12 November 2017 07:21 am

If you have access to a power supply try letting the contents fall into a bucket then position a vacuum cleaner nossle near but not too close to the outlet and the bucket It will take % 99 of the airbourne dust particals from the bucket and crusher for you. Obviously you will need to tap the filter out later but you can do that inside a plastic bag or somewhere less annoying. I had to crush some rock up in the suburbs once and had to do this. Looks like a great little crusher by the way thumbsup

#4

Goldfreak
Member
Joined: 13 May 2017
Posts: 810
Member
12 November 2017 07:22 am

Just noticed you have a makita. Maybe one of there 18v vacuums would work if you dont have a plug to use.

Last edited by Goldfreak (12 November 2017 07:23 am)

#5

Jaros
Moderator
From: S.E.Qld., QLD
Joined: 11 August 2013
Posts: 8,032
Moderator
12 November 2017 08:37 am

I like the idea of the rock crusher. thumbsup


Lottsa hope :F1A4M2, Exterra 705 Gold, Ace 250, Aldi detector, ? detector, Garmin Etrex30, 2 sieves,2 pans,2 sluices, Nugget sniffing Cocker Spaniel. X-Pointer PI by Deteknix, Nokta RS Pinpointer, Jobe Knife, Leschke Shovel, Pro-swing 45 Harness, Treasuremate 11 Amp.Gurney gusunder. VK4NLS

#6

Dolphin
Member
Joined: 06 November 2016
Posts: 105
Member
12 November 2017 04:05 pm

Great ideas mate, your a thinking man,
Dolphin.


GPZ 7000. Several DIY Highbankers,various panning and crevassing tools. "In the midst of chaos,there is also opportunity."
"Strategy without tactics is the slowest route to victory. Tactics without strategy is noise before defeat."

#7

Crow Pickens
Member
From: , SA
Joined: 07 June 2017
Posts: 47
Member
12 November 2017 10:20 pm

Hi.
Thanks for your comments.
Muk. photo of inside. I have only put in two sets of chains, but I have drill the spots for two more if need, it seam to work well with just the two sets.1510484782_4655.jpg
GoldFreak. thanks for your thoughts on vacuum clearner ideal. I seen one being used on a bigger crusher on YouTube. it worked very well for him.
Today I added a PVC pipe bolted onto the end of (sluice) Miller table to catch the heavys before the water goes down into the pump bucket, and I can save on water now. ( less water to carry now, boy water add up in weights very quickly).
1510485241_4660.jpg
Thanks Jaros, Dolphin for comments, and for the PA member for the Likes.
Thanks again.
Cheers Crow Pickens


SDC 2300, Equinox 800, I am a Blessed Man

7 users like this post: Northeast, junkdog, 7.62marksman, Dolphin, Mackka, Wishfull, madtuna

#8

Muk
Member
Joined: 19 June 2016
Posts: 242
Member
13 November 2017 07:59 am

Thanks for the inside photo has given me inspiration to knock one up been thinking about it for awhile now was going to use a old chainsaw for motor but grinder looks the goods lot less noise cheers Muk.

#9

Occasional_panner
Member
Joined: 20 July 2016
Posts: 1,896
Member
13 November 2017 08:24 am

That all looks very well made mate, I reckon you'de sell that stuff easy if you were interested in doing so.

1 user likes this post: Dolphin

#10

Crow Pickens
Member
From: , SA
Joined: 07 June 2017
Posts: 47
Member
19 November 2017 10:46 pm

Hi, Just a update on crusher,
move inlet tube down the bottom, and a bend in the inlet tube to stop most of the small stuff coming back up Tube.1511091784_4668.jpg
Cheers Crow Pickens


SDC 2300, Equinox 800, I am a Blessed Man

3 users like this post: 7.62marksman, Mackka, Occasional_panner

Contact Us - Privacy Policy - Terms Of Service

View Desktop Site

Top